Goldline LOGIC PL-P-4 User Manual download pdf (Page 24)

4. Electrical Wiring

The Pro Logic Control Center requires both high and low voltage connections. Low voltage connections will be made

to actuators, sensors, remote keypad, etc. High voltage connections will be made to pumps, lights, etc., as well as

providing direct input power to the Control Center. Always:

-Ensure that Power is disconnected prior to doing any wiring

-Follow all local and NEC (CEC if applicable) codes

-Use copper conductors only

Main Service (Power to the Circuit Breaker Subpanel)

The Pro Logic circuit breaker subpanel is rated for 100A service. Run properly rated conductors (L1, L2, N, and

ground) from the primary house electrical panel to the main power connections on the Pro Logic circuit breaker base.

The connection at the main house panel should be to a 240VAC circuit breaker rated at 100A maximum.

Grounding and Bonding

Connect a ground wire from the primary electrical panel to the Pro Logic ground bus bar. Also ground each piece of

high voltage (120 or 240VAC) equipment that is connected to the Pro Logic control relays or circuit breakers. The

Pro Logic should also be connected to the pool bonding system by an 8AWG (6AWG for Canada) wire. A lug for

bonding (2 for Canada) is provided on the outside/bottom of the Pro Logic enclosure.

Circuit Breaker Installation and Wiring

Circuit breakers are to be supplied by the installer. Refer to the circuit breaker chart on the following page for a list of

suitable circuit breakers that can be used. Follow the code and the circuit breaker manufacturer’s rating requirements

regarding the size and temperature rating for wiring. Note that some pool equipment may be required to be connected

to ground fault circuit breakers—check local and NEC (CEC) codes.

1021

Chemistry Config.

Wizard + to enter

Press to access Chemistry Config. Wizard

Move to previous/next menu item

Chemistry Configuration Wizard

Requires use of the optional AQL-CHEM Sensing Kit. Following the steps of the Chemistry Config.

Wizard will set up the AQL-CHEM to sense ORP and pH levels and, if chlorination is used, can configure

the Pro Logic to generate the correct amount of chlorine to properly sanitize the pool. Refer to the AQL-

CHEM manual for more detailed information.

Pool/Spa Config.

+ to view/change

Pool/Spa Setup

Pool and Spa

Spa Spillover

Enabled

Filter Operation

Spa Spillover

Push to access Pool/Spa options

Rotates between Pool Only (default), Spa Only and

Pool and Spa

Toggle between Enabled and Disabled Spa Spillover

(default)

Toggle between Pool Only and Spa Spillover options

(default)

Move to previous/next configuration menu

Move to next menu item

Move to next menu item or previous/next configuration menu

Move to previous/next configuration menu

if “Pool and Spa” is

selected and

if “Spa Spillover” is enabled

Spa - CountDn

00:30

Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00))

Move to next menu item

if “Pool and Spa” is selected

V1=Aux1, V2=Aux2

Disabled

Toggle between Enabled and Disabled

(default)

if “Pool Only” or “Spa Only” is selected

Move to previous/next configuration menu

Filter Off Valve

Change: Enabled

Toggle between Enabled and Disabled (default)

if “Pool and Spa” is selected

Move to previous/next configuration menu

Pool/Spa Setup

If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and pushing the POOL/

SPA button on the display/keypad will have no effect. If “Pool and Spa” is selected, then the pool/spa

suction and return valve actuators should be connected to the Pro Logic. Pressing the POOL/SPA button

on the display/keypad will allow the homeowner to alternate between pool and spa operation. For more

information on “Pool and Spa”, refer to the Plumbing section on pages 8.

Spa CountDn

This menu will appear only if Pool/Spa Setup is set to “Pool and Spa”. This setting is the time, after you

manually switch the Pool/Spa valves to “Spa Only”, until the Pro Logic automatically returns the valves to

their previous positions. It is programmed in increments of 5 minutes, from “Manual On/Off” (0 minutes) to

“21:00” (21 hours). The filter is forced on during this time period.

Spa Spillover

When spa spillover is “Enabled” and “Pool and Spa”, the homeowner will be able to rotate through “Pool

Only” (both suction and return valves switched to pool), “Spa Only” (both suction and return valves

switched to spa) and “Spillover” (suction valve switched to pool and return valve switched to spa) by

successive presses of the “Pool/Spa button.

Filter Operation

If “Spa Spillover” is selected, the Pro Logic will automatically switch the pool/spa suction and return

valves to “spillover” at the start of the programmed pool filtering time period or when the super-chlorinate

function is turned on. The valves will remain in this position for the remainder of the super-chlorinate

period. This option is usually preferable because both the pool and spa water will be filtered and sanitized.

If “Pool Only” is selected, then the Pro Logic will switch the pool/spa valves to the “pool only” position

at the start of the programmed pool filtering time period or when the super-chlorinate function is turned on.

This may be desirable on some systems with in-floor cleaners because it allows the cleaner to operate all

the time the pool is being filtered and/or the super chlorinate is running.

High Voltage

Relays

“Local” Display

Control Power

Input

pH Dispense

Output

Subpanel

Valve Connectors

Heater Output

Temp Sensor Inputs

External Input

Remote Keypad

Flow Switch

Cell Connector

Wireless Base

Receiver Connector

AQL-CHEM Connector

Ground Bus Bar

Bonding Lug(s)

Siemens

Murray

Manufacturer

Single

Double

Quad

Twin

GFCB

Filler Plates

QP QT

QT QPF

QF3

SUITABLE LISTED BREAKERS

Tightening

Torque

MP-T

MH-T

MH-T MP-GT LX100FP

25lb-in

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 35 36

Comments to this Manuals

No comments

Goldline LOGIC PL-P-4 User Manual Page 24

Comments to this Manuals

Related products and manuals for Above ground pool accessories Goldline LOGIC PL-P-4