Goldline AQL-PS-4 User Manual download pdf (Page 13)

Pool Chlorinator

60%

Adjust the desired chlorinator output for pool (0,1,2,3...9,10,15,20...95,100%)

Move to previous/next menu item

This setting will appear only if the chorinator function is enabled and system has been setup

for “pool only” or “pool and spa”. It will determine the chlorinator output when the system

is operating in pool-only or spa spillover modes. The actual amount of chlorine introduced

into the pool is determined by: this setting, the amount of time the filter pump is running, the

water temperature, and the amount of salt in the water. If the filter pump is running due to the

freeze protection feature, then the chlorinator will not operate during this time.

Set Day and Time

Wednesday 10:37P

Adjust the current day of the week

Move to hours setting

Set Day and Time

10:37P

Adjust the current day of the week

Move to hours setting

Set Day and Time

Wednesday 37

Set Day and Time

Wednesday 10: P

Adjust the current hour (including AM/PM if applicable)

Adjust the current minute

Move to minutes setting

Move to previous/next menu item

Use this function to set the current day of the week and time. These values are used for all

the automatic timeclock functions of the Aqua Logic and are also displayed as part of the

default menu.

The Aqua Logic is designed to keep the clock running during power outages lasting less

than 7 days. If power has been off for longer than 7 days, then the time may have to be reset.

Display Light

On for 60 sec

Toggle between Always On and On for 60 sec.

Move to previous/next menu item

This function controls the blue backlight on the display. If the “On for 60 seconds” option

is selected, then the backlight will automatically turn off 60 seconds after the last key is

pressed and will stay off until next time a key is pressed.

Note that the Display Light selection only applies to the display keypad that you are currently

using. Other display/keypads will not be affected. You need to individually set this option

for each display/keypad in the system.

Beeper

Enabled

Toggle between

Enabled (default) and Disabled Beeper

Move to next menu item

When “Enabled”, the keypad will beep every time a key is pressed. If this audible indication

is not desired, select “Disabled”.

This function only applies to the display/keypad that you are currently using. You need to

set this option for each display/keypad in your system.

NOTE: This function is not supported on all display/keypads. If the “Enabled” selection is

not blinking, then the current software revision of that particular keypad/display does not

support the option and it will default to Beeper Enabled.

Chlorinator Operation / Water Chemistry

General Water Chemistry

Salt is required only if you are using the chlorinator features on the Aqua Logic Control. If you are NOT

using the chlorinator, it is recommended that you follow all of the other chemistry recommendations be-

sides salt. Refer to the description of the Aqua Logic configuration menu for information on enabling/

disabling the chlorinator (see page 16).

Water Chemistry

The table below summarizes the levels that are recommended by the Association of Pool and Spa Profes-

sionals (APSP). The only special requirements for the Aqua Logic are the salt level and stabilizer.

Saturation index

The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool

water “balance”. Your water is properly balanced if the Si is 0 ±0.2. If the Si is below -0.2, the water is

corrosive and plaster pool walls will be dissolved into the water. If the Si is above +0.2, scaling and

staining will occur. Use the chart below to determine the saturation index.

Gallons

Liters

(pool size in feet)

(pool size in meters)

Rectangular

Round

Oval

Diameter x Diameter x

Average Depth x 5.9

Length x Width x

Average Depth x 6.7

Length x Width x

Average Depth x 7.5

Diameter x Diameter x

Average Depth x 785

Length x Width x

Average Depth x 893

Length x Width x

Average Depth x 1000

ºC ºF

Calcuim

Hardness

Tot al

Alkalinity

103

How to use: Measure pool pH, temperature, calcium hardness,

and total alkalinity. Use the chart above to determine Ti, Ci,and

Ai from your measurements. Insert values of pH, Ti, Ci and Ai

into the above equation. If Si equals .2 or more, scaling and

staining may occur. If Si equals -.2 or less corrosion or irritation

may occur.

Si = pH + Ti + Ci + Ai - 12.1

-.2

0.2

CORROSIVE SCALING

75 75

100 100

125 125

150 150

200 200

250 250

300 300

400 400

600 600

800 800

1.5 1.9

1.6 2.0

1.7 2.1

1.8 2.2

1.9 2.3

2.0 2.4

2.1 2.5

2.2 2.6

2.4 2.8

2.5 2.9

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 45 46

Comments to this Manuals

No comments

Goldline AQL-PS-4 User Manual Page 13

Comments to this Manuals

Related products and manuals for Above ground pool accessories Goldline AQL-PS-4