Goldline AQL-PS-4 User Manual download pdf (Page 30)

A table of functions and their corresponding control parameters are listed below.

Note that all functions in the table may not be offered. The available functions are dependent on how the

Aqua Logic is configured. For example, if the Aqua Logic is configured for a single heater, “Heater2” will

not be available as an option in the Group menu. Also, under some circumstances, functions will be

displayed but can’t be changed. Note that the function whose menu you are in, will not be displayed as an

option and will automatically turn on when the group is activated. For example, if programming a Group

function under the Lights menu, the Lights function will not be offered as an option and the Lights function

will automatically turn on with the group.

The available control parameters vary with each function. All functions offer “Unaffected”, which should

be selected if you do not wish to control that particular function within the group. All other parameters will

depend on the particular function selected.

When activating Group functions, be aware that the most recent Group function that you activate will

override any previous Group functions.

Heater Setpoints in Groups

The Aqua Logic can be programmed to use alternate heater setpoints (conventional and/or solar) while

running group commands. This allows the heater to be set to a higher or lower temperature than normal,

while the group is activated. When the group stops, the setpoint will return to its normal setting.

Changing the setpoint while the Group is running will make the Group release the alternate setpoint control

and revert back to the normal heater setting. Any changes that are made at that point will affect the normal

heater setting. The next time the Group is activated, the temperature will return to the group setpoint that

was originally programmed in the Configuration Menu. To change the setpoint while the Group is running,

go to the Settings menu and press the +/- button while “Group Control” is displayed. The setpoint will

change and be retained as the new normal heater setpoint.

Pool/Spa Unaffected, Pool only, Spa only, or Spillover

Pool Filter Unaffected, Off, On, High speed, or Low speed

Function Control Parameter

Lights Unaffected, Off, or On

Lights Unaffected, Off, On, 100%, 80%, 60%, 40%, or 20%

Spa Filter Unaffected, Off, On, High speed, or Low speed

Aux1-14 Unaffected, Off, On

Aux1-14 Unaffected, Off, On, 100%, 80%, 60%, 40%, or 20%

Valve3 Unaffected, Off, or On

Valve4 Unaffected, Off, or On

Spa Htr1 Set Unaffected, Off, 65º-104ºF

Pool Htr1 Set Unaffected, Off, 65º-104ºF

Spa Htr2 Set Unaffected, Off, 65º-104ºF

Pool Htr2 Set Unaffected, Off, 65º-104ºF

Spa Solar Set Unaffected, Off, 65º-104ºF

Pool Solar Set Unaffected, Off, 65º-104ºF

SuperChlr Unaffected, Off, On

(standard relay)

(dimmer relay)

tandard relay)

Countdown Timer – the valve3 relay will turn on when the VALVE3 button is pressed and

then will turn off automatically after a programmed time (see Timers Menu in the Operations

Manual). The VALVE3 button can also be used to turn the output off.

Timeclock – the valve turns on/off at the times set for the valve3 timeclock in the Timers

Menu (see Operations Manual). The valve3 button can also be used to turn the valve output

on or off.

Solar – the valve operates when the filter pump is running

and solar heat is available and the

water is less than the desired temperature setting. Solar heating must be enabled in the

“Solar Config. menu for proper operation to occur.

In-Floor Cleaner – the valve switches the water returning to the pool between the in-floor

cleaner and the normal return jets which facilitate efficient surface skimming. The valve will

operate the in-floor cleaner for the first half of each clock hour and then switch to the jets/

skimming for the last half of the hour.

Group – the valve operates when the Group function is initiated and shuts off when the

Group function is terminated. See valve3 Group section for operation information for the

Group function.

Super Chlorinate – The Super Chlorinate function can be assigned to any Aux, Lights or

Valve button. This allows the user to simply hit a button to start a Super Chlorinate cycle,

rather than using the Settings Menu. Note that only one button can me assigned to this

function.

Valve3 Interlock

If “Enabled”, this feature will override the function (timeclock, manual on/off, countdown

timer or in-floor cleaner) selected above and turn the valve off whenever the filter pump is off

or the pool/spa suction/return valves are set to “spa only” or “spillover” operation. Interlock

is not available with solar or group.

Valve3 Group

The valve3 Group function allows the user to perform multiple tasks with a single push of the

VALVE3 button. When setting up a Group function, refer to page 22 for specific programming

information. There are two Group menus; the first menu determines how the group command

will be initiated (Manual On/Off, Countdown Timer, or Timeclock) and the second menu

selects the desired functions and their respective control parameters.

When activating Group functions, be aware that the most recent Group function that is

initiated will override any previous Group function.

Valve3 Freeze Protection

This function protects the pool and plumbed equipment against freeze damage. If Freeze

Protection is enabled and the AIR temperature falls sensor falls below the selected freeze

protection temperature, the Aqua Logic will turn on the valve to allow circulation of the

water. IMPORTANT: this only enables operation of the valve3 output during freeze--see the

“Filter Pump Config.” menu to enable freeze protection for the main circulation system.

Freeze protection is not available for group functions.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 45 46

Comments to this Manuals

No comments

Goldline AQL-PS-4 User Manual Page 30

Comments to this Manuals

Related products and manuals for Above ground pool accessories Goldline AQL-PS-4