Goldline AQL-PS-4 User Manual download pdf (Page 27)

when the super-chlorinate function is turned on. The valves will remain in this position for

the remainder of the super-chlorinate period. This option is usually preferable because both

the pool and spa water will be filtered and sanitized.

If “Pool Only” is selected, then the Aqua Logic will switch the pool/spa valves to the “pool

only” position at the start of the programmed pool filtering time period or when the super-

chlorinate function is turned on. This may be desirable on some systems with in-floor

cleaners because it allows the cleaner to operate all the time the pool is being filtered and/or

the super chlorinate is running.

V1=Aux1, V2=Aux2

This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled,

Valve 1 (return) will follow the Aux1 output and Valve 2 (suction) will follow the Aux2 output.

When disabled (default), the return and suction pool/spa valves function normally.

Filter Off Valve Change

This menu appears only if Pool/Spa setup is set to “Pool and Spa”. When enabled (default),

the filter pump will shut off for 35 seconds whenever the Pool/Spa valves are turning. The

pump will NOT shut off when the heater has Cooldown enabled and is either on or in the

Heater Cooldown mode.

Filter Pump Config.

+ to view/change

Filter Name

Pool Filter

Filter Pump

1 Speed

Freeze Protect

Enabled

Flow Monitor

Disabled

Freeze Temp

38ºF

Push to access pump options

Rotates between all available names

Toggle between 1-speed (default) and 2-speed options

Toggle between Enabled (default) and Disabled Freeze Protection

Toggle between Enabled and Disabled Flow Monitor (default)

Adjust the desired freeze protection temperature (33ºF - 42ºF)

Move to next menu item

Move to previous/next configuration menu

Move to next menu item

Move to next menu item or previous/next configuration menu

Move to next menu item

Move to previous/next configuration menu

if “Freeze Protect” is enabled

Filter Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Filter Pump, Pool

Filter, Spa Filter, etc.) to the filter relay. This will make the Aqua Logic more user friendly to the

homeowner when they want to control the filter equipment. A sheet of small name labels is

included with the Aqua Logic main unit and each remote display/keypad so that appropriate

pushbuttons can be labeled the same as the name that you have assigned.

Filter Pump

For 2-speed pumps: When a 2-speed pump is configured, one of the AUX relays must also

be configured to control the low speed motor winding on the pump (see page 14 for wiring

and page 31 for AUX configuration). See the Operation manual for specific information

regarding the control logic for 2-speed pump operation.

Flow Monitor

This feature will help protect the filter pump from damage due to no flow. When used with a

Goldline flow switch, the Aqua Logic monitors the state of water flow when the filter pump is

on. If no flow is detected for more than 15 minutes, the Aqua Logic will shut down the pool

pump and the “Check System” LED will indicate an error. The error will be cleared the next

time the pump is turned on.

and page 31 for AUX configuration). See the Operation manual for specific information

regarding the control logic for 2-speed pump operation.

Freeze Protection

Freeze protection is used to protect the spa and plumbed equipment against freeze damage.

If freeze protection is enabled and the AIR temperature sensor falls below the freeze threshold

(selectable in Filter Pump Configuration Menu - page 25), the Aqua Logic will turn on the spa

filter pump to circulate the water.

NOTE: The configuration parameters for all Aux outputs are same as shown below for Aux1. PS-4: Aux1 and Aux2.

PS-8: Aux1 through Aux6. PS-16: Aux1 through Aux14. Also note that for the PS-16, Valves7, 8, 9 and 10 are turned

On/Off with the control function selected for Aux7, 8, 9, and 10, respectively.

Aux1 Config.

+ to view/change

Aux1 Function

Manual On/Off

Aux1 Group

Filter: Unaffected

Aux1 Group

Timer: None(Manual)

Aux1 Name

Cleaner

Aux1 Relay

Standard

Push to access Aux options

Options available depend on the function that is selected

Rotates between Manual On/Off (default),Countdown Timer and Timeclock

Rotates between all available names

Toggle between Standard (default) and Dimmer

Move to previous/next configuration menu

Move to previous/next menu item or next configuration menu

Move to next configuration menu item

Move to next menu item

Move to next menu item or previous/next configuration menu

Aux1 Interlock

Disable

Aux1 Freeze

Disable

Toggle between Enabled and Disabled (default) Aux1 Interlock

Toggle between Enabled and Disabled Aux1 Freeze(default)

Move to next menu item

Move to previous/next configuration menu

for all functions except solar, dimmer relay,

low speed (filter pump), and group

for all functions except dimmer relay,

low speed, and group

for group function only

for manual on/off, countdown

timer and timeclock functions

Rotates between

Manual On/Off (default), Countdown Timer, Low Speed-

Filter, Timeclock, Solar, Low speed-Spa Filter, Group & Super Chlorinate

Move to next menu item

WARNING: Do not use the Aqua Logic to control an automatic pool cover. Swim-

mers may become entrapped underneath the cover.

NOTE: If “Pool and Spa-Dual” is selected, Aux1 is dedicated to use as the spa filter. Its Name is set to Spa Filter, the

Function is set to Timeclock and Interlock is set to Disabled. These can’t be changed.

Aux1 Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Cleaner Pump,

Waterfall, Gazebo Light, etc.) to each of the aux outputs control function. This will make the

Aqua Logic much more user friendly to the homeowner when they want to turn various aux

equipment on or off or program the timeclocks. A sheet of small name labels is included with

the Aqua Logic main unit and each remote display/keypad so that the “Aux” pushbutton can

be labeled the same as the name that you have assigned. At this time it is also a good idea to

make sure that the relay in the control box is also labeled (hand written) with the same name

as a help to technicians who may service this system at a later date.

Aux1 Function

Manual On/Off (default)—the aux relay will alternate between turning on and off when the

aux button is pressed. There is no automatic control logic.

Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will

turn off automatically after a programmed time (see Timers Menu in the Operations Manual).

The AUX button can also be used to turn the output off.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 45 46

Comments to this Manuals

No comments

Goldline AQL-PS-4 User Manual Page 27

Comments to this Manuals

Related products and manuals for Above ground pool accessories Goldline AQL-PS-4