Goldline AQL-PS-4 User Manual download pdf (Page 21)

Pool/Spa Config.

+ to view/change

Pool/Spa Setup

Pool and Spa-Std

Spa Spillover

Enabled

Heaters

Htr1=Spa,Htr2=Pool

Filter Operation

Spa Spillover

Push to access Pool/Spa options

Rotates between Pool and Spa-Std , Pool and Spa-Dual,

Pool Only, and Spa Only options

(default)

Toggle between Enabled and Disabled Spa Spillover(default)

Toggle between Htr1=Spa, Htr2=Pool (default) and Shared Heaters

Toggle between Pool Only and Spa Spillover options(default)

Move to previous/next configuration menu

Move to next menu item

Move to next menu item or previous/next configuration menu

Move to next menu item

Move to previous/next configuration menu

if “Pool and Spa-Std or Dual” is

selected and if “Spa Spillover” is enabled

Spa - CountDn

00:30

Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00))

Move to next menu item

if “Pool and Spa-Std” is selected

if “Pool and Spa-Dual” is selected

if “Pool and Spa-Std or Dual” is selected

V1=Aux1, V2=Aux2

Disabled

Toggle between Enabled and Disabled

(default)

if “Pool Only” or “Spa Only” is selected

Move to previous/next configuration menu

Filter Off Valve

Change: Enabled

Toggle between Enabled and Disabled (default)

if “Pool and Spa-Std” is selected

Move to previous/next configuration menu

Pool/Spa Setup

If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and

pushing the POOL/SPA button on the display/keypad will have no effect. If “Pool and Spa-

Std” is selected, then the pool/spa suction and return valve actuators should be connected

to the Aqua Logic. Pressing the POOL/SPA button on the display/keypad will allow the

homeowner to alternate between pool and spa operation. If “Pool and Spa-Dual” is selected,

then only the Pool/Spa return valve actuator should be connected to the Aqua Logic.

For more information on “Pool and Spa-Std” and “Pool and Spa-Dual”, refer to Section 3,

Plumbing, on pages 9-12.

Heaters

This menu will only appear if Pool/Spa setup is set to “Pool and Spa-Dual”. This allows the

heater(s) to either be shared between the pool and spa (“Shared” selected) or for Heater1 to

be dedicated to the spa and Heater2 to be dedicated to the pool (“Htr1=Spa, Htr2=Pool”

selected).

Spa CountDn

This menu will appear only if Pool/Spa Setup is set to “Pool and Spa-Std”. This setting is the

time, after you manually switch the Pool/Spa valves to “Spa Only”, until the Aqua Logic

automatically returns the valves to their previous positions. It is programmed in increments

of 5 minutes, from “Manual On/Off” (0 minutes) to “21:00” (21 hours). The filter is forced on

during this time period.

Spa Spillover

When spa spillover is “Enabled” and “Pool and Spa-Std”, the homeowner will be able to

rotate through “Pool Only” (both suction and return valves switched to pool), “Spa Only”

(both suction and return valves switched to spa) and “Spillover” (suction valve switched to

pool and return valve switched to spa) by successive presses of the “Pool/Spa” button. For

“Pool and Spa-Dual”, only “Pool Only” and “Spillover” are available.

Filter Operation

If “Spa Spillover” is selected, the Aqua Logic will automatically switch the pool/spa suction

and return valves to “spillover” at the start of the programmed pool filtering time period or

Low Speed of a 2-speed Filter Pump – the Aqua Logic will operate the aux relay whenever

the low speed operation of the filter pump is required. It is very important that the “2-speed”

filter pump option be selected under the “Filter Config.” Menu for proper operation.

Timeclock – the aux relay will turn-on and turn-off at the times set for the aux timeclock in the

Timers Menu (see Operations Manual). The AUX button can also be used to turn the

output on and off.

Solar – the aux relay operates a solar booster pump which will turn on when the filter pump

is running and solar heat is available and the water is less than the desired temperature

setting. It is important to note that “Solar” must be enabled in the “Solar Config.” menu for

proper operation to occur.

Low Speed of a 2-Speed Spa Filter Pump – the Aqua Logic will turn on the aux relay

whenever the low speed operation of the Dual Equipment Spa filter pump is required. “Pool

and Spa-Dual” (located in Pool/Spa Setup menu) and “2-Speed” (located in Spa Filter Config.

menu) must be selected for proper operation.

Group – the aux relay operates when the Group function is initiated and shuts off when the

Group function is terminated. See Aux1 Group section for operation information for the

Group function.

Super Chlorinate – The Super Chlorinate function can be assigned to any Aux, Lights or

Valve button. This allows the user to simply hit a button to start a Super Chlorinate cycle,

rather than using the Settings Menu. Note that only one button can me assigned to this

function.

Aux1 Relay

This feature allows the user to select either “Standard” (default) or “Dimmer” type relay for

the Aux1 output. The optional AQL-DIM dimmer kit must be installed if “Dimmer” is desired.

When “Dimmer” is selected, and the Aux1 output is manually turned on, the “+” and “-”

buttons adjust the level from 20% to 100% (default). The level is saved for the next time the

aux1 output is turned from off to on.

Aux1 Interlock

If “Enabled”, this feature will override the function (Manual On/Off, Countdown Timer,

Timeclock), selected above and turn the aux1 off when: filter pump is off, first 3 minutes of

filter pump operation (allows the pump to prime and get water flowing), when the pool/spa

suction return valves are in any position other than “pool only”, or for the first 3 minutes

after solar turns on (allows air in the solar panels to be purged). Interlock is not available for

solar, low speed filter pump, dimmer, or group functions.

Aux1 Group

The Aux1 Group function allows the user to perform multiple tasks with a single push of the

“Aux1” button. When setting up a Group function, refer to page 22 for specific programming

information. There are two Group menus; the first menu determines how the group command

will be initiated (Manual On/Off, Countdown Timer, or Timeclock) and the second menu

selects the desired functions and their respective control parameters.

When activating Group functions, be aware that the most recent Group function that is

initiated will override any previous Group function.

Aux1 Freeze Protection

This function protects the pool, plumbing, and equipment against freeze damage. If Freeze

Protection is enabled and the AIR temperature sensor falls below the selected freeze protection

temperature, the Aqua Logic will turn on the aux relay to circulate the water. IMPORTANT:

this only enables operation of the AUX output during freeze--see the “Filter Pump Config.”

menu to enable freeze protection for the main circulation system. Freeze Protection is not

available for low speed filter pump, dimmer, or group functions.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 45 46

Comments to this Manuals

No comments

Goldline AQL-PS-4 User Manual Page 21

Comments to this Manuals

Related products and manuals for Above ground pool accessories Goldline AQL-PS-4